一、要留意鐫刻機的功效。這種工藝已盛行一段光陰，但由于鐫刻功率太小而大大影響了其軟件范圍。另一種是大功率鐫刻頭的鐫刻機，這種鐫刻機有分為兩類，一類是大幅面切割機：幅面普通在一米以上，但這種鐫刻機的精度普通較差；另一類是幅面適中的鐫刻機：這種鐫刻機普通軟件于精細加工和有機標牌制作。

1、 Pay attention to the effectiveness of the engraving machine. This technique has been popular for some time, but its software range has been greatly affected due to the low engraving power. Another type is the engraving machine with high-power engraving heads, which can be divided into two categories. One is the large format cutting machine: the format is usually over one meter, but the accuracy of this engraving machine is generally poor; Another type is the engraving machine with moderate size: this type of engraving machine is commonly used for fine processing and organic label production.

二、要打聽鐫刻電機的性能和功效。而鐫刻頭電機又是長光陰連續兼職的因此如果鐫刻頭電機欠好也會影響鐫刻機的軟件。普通速度可調范圍是每分鐘幾千到三萬轉。

2、 To inquire about the performance and effectiveness of engraving motors. And the engraving head motor is a long-term continuous part-time job, so if the engraving head motor is not good, it will also affect the software of the engraving machine. The adjustable range of normal speed is several thousand to thirty thousand revolutions per minute.

三、鐫刻機的鐫刻頭電機也是很環節的因為鐫刻頭電機普通都不屬于保修范圍，絲桿和導軌也是鐫刻機的重要組成部分。好的絲桿和導軌是鐫刻機永遠軟件時其精度和性能的包管。

3、 The engraving head motor of the engraving machine is also a very important part because engraving head motors are generally not covered by warranty, and the screw and guide rail are also important components of the engraving machine. A good screw and guide rail are the guarantee of the accuracy and performance of the engraving machine's software.

四、再者即是鐫刻頭電機的速度可調范圍。若速度不行調或速度可調范圍較小，辣么就分析該鐫刻機軟件范圍就受到很大的限制，因為鐫刻差別的資料必需用差別的鐫刻頭轉速。

4、 Furthermore, the speed range of the engraving head motor can be adjusted. If the speed cannot be adjusted or the adjustable range of speed is small, the software range of the engraving machine will be greatly limited, because different engraving data must be engraved with different engraving head speeds.

五、控制器普通也分為兩類：一類控制器只是做驅動。鐫刻機兼職時電腦處于等待狀態，無法進行排版兼職。另一類控制器采用單板機或單片機控制，這種控制器實際上即是一臺電腦，因此只要鐫刻機一開始兼職，電腦馬上便進行其余排版兼職，特別是較長光陰鐫刻時，該上風特別明顯。

5、 Controllers are generally divided into two categories: one type only serves as drivers. When the engraving machine is working part-time, the computer is in a waiting state and cannot perform typesetting part-time. Another type of controller is controlled by a single board computer or microcontroller, which is actually a computer. Therefore, as soon as the engraving machine starts working part-time, the computer immediately takes on other typesetting tasks, especially when engraving for a longer period of time. This advantage is particularly evident.

六、鐫刻機本體制造工藝：大功率鐫刻機兼職時要求本體必然要精密和穩定。臨時大功率鐫刻應采用鑄造本體才干包管其加工精度和穩定性。而其所有運算兼職由電腦來實現。

6、 Manufacturing process of engraving machine body: High power engraving machines require precision and stability when working part-time. Temporary high-power engraving should use a cast body to ensure its machining accuracy and stability. And all of its calculations are implemented by computers.

本文由穿條機友情奉獻.更多有關的知識請點擊:http://yggggs.com/真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

This article is a friendly contribution from the threading machine. For more related knowledge, please click: http://yggggs.com/ Sincere attitude. We provide you with excellent service. We will gradually contribute more knowledge to you. Please stay tuned